Glock MOS Footprint: 6 Plates, 100 Red Dots, 1 Direct

By CaliberAPI Ā· Ā· 15 min read

Last verified October 27, 2026

glockglock mosplate systemsfootprints

There is no Glock MOS footprint. MOS is a plate pocket: Glock mills the slide for a removable adapter plate, and the plate, not the slide, carries the pattern your red dot bolts to. That is why this dataset records the 15 Glock MOS pistols in it as reaching 100 of its 112 optic pages while recording exactly 1 optic that fits the MOS cut itself. The other 99 arrive through one of 6 plate paths. So the question ā€œwhat red dot fits a MOS Glockā€ has no useful answer until you have answered a narrower one: which plate.

Every number here is recomputed from the published dataset bundle for this article. That bundle holds 223 optic-ready pistols, 112 optic pages covering 151 individual SKUs, and 42 footprint and plate-system hubs, 11 of them real footprints and 31 of them plate systems like this one. Glock MOS is the largest of those 31 by pistol count, at 15 pistols, one ahead of the S&W M&P CORE at 14.

Glock’s four plates, and the two it does not make

Glock publishes its MOS plates by optic group and slide width (eu.glock.com). ā€œFor GLOCK pistols in MOS configuration slide width 25,5 mm / 1.00 inā€, it lists four numbered plates, and the same four groups again as 05 to 08 for slides of 27.5 mm and 28.5 mm. Glock’s adapter set sheet adds the screw thread for each (adapter set 01 to 08 sheet):

Optic group (Glock’s wording)Plate, 25.5 mm slidePlate, 27.5 and 28.5 mm slidesScrew threadPattern recorded here
Docter, Meopta, Insight, Vortex, Burris0105M3Docter
Trijicon, Holosun (except 509), Ameriglo02066 to 32 UNCRMR
C-More03078 to 32 UNCC-More STS
Leupold, EOTech0408M4DeltaPoint Pro

Glock lists no Aimpoint and no Shield group. The two plates that fill those gaps come from the optic makers themselves. Aimpoint sells a Glock MOS ACRO mount plate, item 200520, ā€œFor mounting ACRO sights on optic ready Glock MOS handgunsā€ (aimpoint.us). Shield Sights sells a GLOCK MOS low-profile mounting plate ā€œdesigned for the SHIELD footprintā€ (shieldsights.com). This dataset credits each plate to the company that makes it.

The six plate paths

The Glock MOS plate system hub records six plate paths. Each plate presents exactly one footprint, and that footprint is the entire shopping list.

PlatePresentsOptics reachableOptic brandsEnclosed emitterFlagged verified
Glock 02 / 06RMR358435
Shield Sights MOS plateRMSc34141034
Glock 04 / 08DeltaPoint Pro165516
Glock 01 / 05Docter6406
Aimpoint MOS plateACRO7477
Glock 03 / 07C-More STS1101

Those six counts sum to 99 exactly, which means no optic in this dataset sits on two of the six plates. There is no hedging plate and no overlap to fall back on. Whichever plate goes in the pocket deletes at least 64 of the 99 candidates before you have read a single reticle spec.

The RMR plate has the longest list at 35 optics but a narrow brand spread at 8 makers, because Holosun alone supplies 16 of those 35 and Swampfox another 5. The Shield Sights plate reaches 1 fewer optics across 14 makers, including all 7 Shield Sights products here. If your shortlist is a brand rather than a model, the RMSc plate is the wider door despite the smaller number.

The ACRO plate is the one that looks marginal and is not. All 7 of its optics are enclosed emitter designs, and between the ACRO, RMSc, DeltaPoint Pro and RMR plates a MOS Glock reaches 26 of the 34 enclosed optics in this dataset.

All 15 MOS pistols reach the same 100 optics

This is the part that makes most MOS buying guides noise. The 15 pistols on this system do not merely reach similar numbers of optics. They reach one identical set, checked element by element for this article: the compatible optic set of the Glock 17 Gen4 MOS is the same 100 slugs as the 26 Gen5 MOS, the 34 Gen5 MOS, the 45 MOS, the 47 Gen5 MOS and the 19 Gen5 MOS. Frame size, generation and caliber move nothing. Only the plate does, and on the 27.5 mm and 28.5 mm wide slides Glock lists separately, only the plate’s number changes.

Across the whole Glock lineup here the split is three ways:

Glock pistolsHow the optic mountsOptics reachable
15 MOS plate-system modelsplate pocket, 1 exception100
2 slimline MOS modelsmilled RMSc cut, no plate34
3 Gen6 modelsGlock Gen6 OR plates, not MOS52

The Gen6 guns, the G19 Gen6, G17 Gen6 and G45 Gen6, ship with their own set of three Glock OR plates (02, 03 and 04) rather than a MOS plate, so they are filed under the separate Glock Gen6 OR plate system (us.glock.com).

Those two slimline guns are the 43X MOS and the 48 MOS, and they are the single most expensive confusion attached to the three letters. Their slides are cut for the Shield RMSc pattern, so an RMSc optic bolts straight down and there is no plate in the system at all (optics-trade.eu, swampfoxoptics.com). Same badge, different mounting standard, no shared parts, and a 66 optic page difference in what you can buy.

Where 100 actually ranks

Only 37 of the 223 pistols here reach more than 100 optics: the 7 Walther PDP 2.0 models at 101 and four SIG P320s at 101, the M17, M18, X-Five Legion and XCarry Legion. The 15 MOS Glocks are the only pistols at exactly 100, and the median pistol reaches 58. A MOS Glock sits near the top of the catalogue.

Among the 31 plate systems it places second. The table below lists the plate systems that reach more than half the optic pages, each measured on its own plate paths and built-for-the-cut optics, with two columns no hub page can carry: what that system reaches which a MOS Glock cannot, and the reverse.

Plate systemPistolsPathsOpticsReaches, MOS cannotMOS reaches, it cannot
Walther PDP 2.07610132
Glock MOS15610000
Springfield XD OSP359769
Walther PDP 1.0159802
Springfield Echelon VIS759802
SIG P320 Outer Impact559208
Ruger factory plate159208
Canik METE159208
Springfield AOS649109
Canik SFx Rival249109
HK VP9A13791817
Canik TTI Combat1269031
S&W M&P CORE14566842
FN 50912566842

Read the two right-hand columns and the shape of the system falls out.

MOS is a superset of most of the large systems. Eight rows show 0 in the ā€œreaches, MOS cannotā€ column: there is nothing the Walther PDP 1.0, the Echelon, the Outer Impact P320 plates, the Ruger plate, the Canik METE and SFx Rival plates, the AOS or the TTI Combat can mount that a MOS Glock cannot. What MOS adds over them is some mix of the ACRO plate, the Shield plate, the C-More plate and the one direct fit.

The systems that beat it, or trade with it, do so on Holosun patterns. The Walther PDP 2.0 reaches 101 because it carries a Holosun 509T plate, worth the AEMS-MACRO and the HE509T-X2, and its own direct-fit SCS-PDP-GR; it lacks the C-More plate and the MOS direct fit. The XD OSP trades its ACRO and C-More gaps for a Holosun K plate, 6 optics MOS has no plate for. The C&H Precision plate systems, the M&P CORE and the FN 509 rows, reach the Holosun K and 509T optics but none of the RMSc or Docter optics, which is why they sit 34 below MOS.

A pistol can beat MOS by carrying two systems. The four P320s at 101 combine SIG’s direct DeltaPoint Pro cut with both the C&H Precision and the Outer Impact plate sets. Against a MOS Glock they add the two 509T optics and lack only the SCS-M-GR.

The Docter plate is the gap that used to be quoted

Older MOS guides, including earlier data on this site, said a MOS Glock had no Docter plate, so a Vortex Venom or Viper owner was stuck. Glock’s own list says otherwise: plate 01 (05 on the wider slides) is for ā€œDocter, Meopta, Insight, Vortex, Burrisā€. In this dataset the 6 Docter pattern optics now reach 69 of the 223 pistols through 18 plate paths, the Glock plate among them, and a Vortex Venom fits 69 pistols, all 15 MOS Glocks included. The same correction adds the C-More plate, 03 (07), which brings the Primary Arms GLx RS-15, the one C-More pattern optic in this dataset.

Four facts in Glock’s plate table

The number alone is not enough. 01 and 05 are the same optic group on different slide widths, so a plate bought by number without the width is a coin flip. Measure the slide across its flats before ordering.

The screw thread changes with the plate. M3, 6 to 32 UNC, 8 to 32 UNC and M4 are four different fasteners, which is why Glock’s instruction is to use only the screws supplied with the plate and why a spare screw from the last optic is not a spare screw for this one.

One set, one plate. Glock’s page reads ā€œONE GLOCK MOS ADAPTER PLATE SET CONTAINS One numbered GLOCK MOS Adapter Plateā€. Buy the set for your optic group, not a bag of every plate.

Glock’s groups are brand groups, not footprints. ā€œHolosun (except 509)ā€ is the Trijicon plate because most Holosun optics share the RMR pattern; the 509T uses its own rail and clamp, and no MOS plate recorded here presents it. Read your optic’s pattern off its own page before trusting the brand label.

How to tell what you are holding

Four checks, in the order that settles the question fastest.

  1. Look into the cut. Take the cover plate off the rear of the slide. A MOS pocket is a blank rectangular recess with two screw holes and nothing standing proud inside it. This dataset records the MOS cut as 2 retention screws and publishes no boss count for it, which is the right answer for a pocket: the plate carries the bosses. If instead you can see posts or sockets raised inside the cut, the slide is milled for a footprint directly and no plate belongs in it.
  2. Check the box, not the slide marking. A plate-system MOS pistol ships with a numbered plate and its screws. A slimline 43X MOS or 48 MOS ships with a cover plate and nothing else, because there is nothing to adapt.
  3. Measure the slide width. 25.5 mm takes plates 01 to 04, and 27.5 mm or 28.5 mm takes 05 to 08 for the same optic groups. This is the step that gets skipped and the step that decides whether the plate you ordered fits.
  4. Read the optic’s pattern off the optic, not the brand. Several makers sell the same model in more than one footprint. The optic pages here each state the pattern and cite the source for it, for example the Holosun SCS-M-GR, which states Glock MOS rather than a footprint because it is the exception.

The one optic that skips the plate

The Holosun SCS-M-GR is built for the pocket itself. It drops into the MOS cut and bolts down with no adapter under it (holosun.com), and it fits all 15 MOS pistols in this dataset and no others. It is 1 of 2 optics in the whole catalogue here that mount a plate system directly; the other is the PDP version of the same sight, which reaches the 7 Walther PDP 2.0 pistols and nothing else.

Two things to know before treating it as the easy answer. It is an open emitter sight, so the no-plate route and the sealed-optic requirement are mutually exclusive on this pistol: if you want an enclosed emitter you are buying a plate. It is flagged verified against that page, but it carries a single source URL, its own product page, so its record rests on one read.

Choosing, framed by the data

If you already own the optic, the optic decides everything. Read its pattern, then buy the plate for that pattern: Glock’s number and your slide width for Docter, RMR, C-More and DeltaPoint Pro, or the Aimpoint or Shield Sights plate for an ACRO or a Shield RMSc pattern optic.

If you are choosing the optic now, choose the plate first. The six paths are 35, 34, 16, 6, 7 and 1 optics wide. Picking the plate first means shopping one of six real lists. Picking the optic first means hoping a plate exists.

If the requirement is an enclosed emitter, this is a strong system. 26 of the 34 enclosed optics here are reachable on a MOS Glock. The 8 it cannot reach are the Holosun K and 509T designs, the SIG-LOC ROMEO-X and the Aimpoint COA, which need cuts no MOS plate here presents.

If the requirement is the lowest possible mount, the plate is the cost. Every one of the 99 plate fits puts an extra interface and extra height between the slide and the dot. The one way around it is the SCS, and that costs you the enclosed emitter.

If you own several pistols, MOS is the widest single standard. Its 15 pistols are the most on any plate system here, and every one of them reaches the same 100 optics.

What this dataset does not know

Stated plainly, because the gaps change how much weight the numbers above deserve.

The plate paths rest on the plate makers’ own pages. Glock’s MOS adapter plate page for the four Glock plates, Aimpoint’s and Shield Sights’ product pages for the ACRO and RMSc plates. The pistol records lean on a Glock MOS overview (all4shooters.com) and one Glock product page, the G35 Gen4 MOS. Glock’s page also says to ā€œconsult your retailer in order to confirm compatibility with specific red dot sight modelsā€, so a pattern match is a strong start, not a guarantee for every body shape.

Nothing here is verified against a physical sample. 112 of the 112 optic pages in this dataset carry a verified flag, which means a source page about that exact model was read and agreed with the record. 100 of the 100 optics reachable on a MOS Glock are in that group, and 51 of the 100 rest on a single source URL. 41 of the 100 publish a window width or height, but no record here pairs that with your sight height, so this dataset cannot tell you whether a given dot clears your suppressor sights.

The pistol count is the number most exposed to duplication. This dataset used to count the Glock 47 twice, as ā€œ47 MOSā€ and ā€œ47 Gen5 MOSā€. They are now one record, the 47 Gen5 MOS, and the old address redirects to it.

Plate pocket geometry is not published here. No pocket dimensions, no screw spacing, no Glock plate drawing is among our sources. The screw threads in the table above come from Glock’s sheet, not from our data. Match a replacement plate by part number against your own pistol.

Sources

Frequently asked

What is the Glock MOS footprint?

There is no Glock MOS footprint. MOS is a plate system: the slide is milled for a removable adapter plate, and the plate carries the footprint the optic bolts to. In this dataset 15 Glock pistols use the system and 6 plate paths reach it: Glock's own plates for the Docter, RMR, C-More and DeltaPoint Pro patterns, Aimpoint's MOS plate for the ACRO and Shield Sights' MOS plate for the Shield RMSc pattern. One optic, the Holosun SCS-M-GR, drops into the pocket with no plate.

RMR vs MOS: which one does my Glock use?

Both, in series, and they are not the same kind of thing. RMR is a footprint, a pattern of two screws and two recoil bosses an optic bolts down onto. MOS is a blank pocket in the slide. A MOS Glock reaches the 35 RMR pattern optics in this dataset through the plate Glock numbers 02 for a 25.5 mm slide (06 on the wider slides), which Glock lists for Trijicon, Holosun except the 509, and Ameriglo. Take the plate out and nothing bolts to the slide.

How many red dots fit a Glock 19 Gen5 MOS?

100 of the 112 optic pages in this dataset, and the number is identical on all 15 MOS pistols here, because they share one plate system. The 100 splits into 1 direct fit plus 35 on the RMR plate, 34 on the Shield RMSc plate, 16 on the DeltaPoint Pro plate, 6 on the Docter plate, 7 on the ACRO plate and 1 on the C-More plate, with no optic on two of them.

Does the Glock 43X MOS use MOS adapter plates?

No, and it is the most expensive mix-up on the name. The 43X MOS and the 48 MOS carry a milled RMSc cut, so an RMSc pattern optic bolts straight to the slide and no plate is involved. Each reaches 34 optics in this dataset against 100 for the 15 plate-system Glocks.

Which MOS adapter plate do I need for my red dot?

The one presenting your optic's pattern, and Glock numbers them by optic group and slide width. On a 25.5 mm slide Glock lists 01 for the Docter, Meopta, Insight, Vortex and Burris group, 02 for Trijicon, Holosun except the 509 and Ameriglo, 03 for C-More and 04 for Leupold and EOTech. Slides of 27.5 mm and 28.5 mm use 05 through 08 for the same groups. Glock makes no ACRO or Shield plate; Aimpoint and Shield Sights sell their own MOS plates for those.