The DPP footprint

The DPP is a pistol optic footprint that mounts with 2 screws (screw_through). 16 red dot optics use the DPP footprint, including the Bushnell RXE-MR1, Bushnell RXS-10 and Bushnell RXS-100. It also mounts on 107 more pistols through an adapter plate.

Leupold DeltaPoint Pro. Two M4 oval-head Torx screws and four corner recoil lug sockets. The standard defines four sockets; some mounts physically include only two of the four pins, but the standard itself is four. Body size approximately 46mm length. The optics on this pattern here are 16 SKUs from five brands: the Leupold DeltaPoint Pro itself, four Vortex (Defender-ST, Defender-ST Enclosed Solar, Defender XL, Venom Enclosed), four Bushnell, four Sig Sauer and three EOTech EFLX models. Two patterns sit close enough to be mistaken for it: the Shield RMS shares the screw and socket layout at a shorter body length and is filed under RMSc, and Docter shares both counts, which is where the Crimson Trace CTS-1250 and the open-emitter Vortex Venom and Viper are filed.

Footprint

DPP

Family:
Leupold DeltaPoint Pro
Screw count:
2
Mounting:
screw_through
Optics:
16
Pistols:
23 direct · 107 via plate

Footprint specifications are compiled from manufacturer drawings and optic spec sheets.

How to identify a DeltaPoint Pro cut without a caliper

Take the cover plate off the slide, or turn the optic over, and read the recess in this order.

  1. Screw holes: two. They sit on the long axis and the optic screws pass down through its body into the slide, a screw-through mount. If the optic instead clamps sideways with a single cross bolt, you are looking at an ACRO or Holosun 509T interface and nothing on this page applies.
  2. Recoil sockets: four, at the corners. Two forward, two rear. Four is the number that rules out the RMR pattern, which puts two bosses forward of the screws and nothing behind them.
  3. Body length: about 46mm, not about 40mm. This is the step most charts skip, and it is the one that decides between this pattern and the RMSc pattern, because those two share both counts. A DeltaPoint Pro sized optic covers a full size slide window; a 40mm micro sits noticeably shorter on the same cut.

One warning about counting on the plate rather than on the optic. The standard defines four sockets, but some mounts are made with only two of the four pins present. A plate with two pins is still a DeltaPoint Pro plate. Count the sockets on the underside of the optic, which are always four, not the pins on whatever it is sitting on (optics-trade.eu).

The reference part is the Leupold DeltaPoint Pro itself (leupold.com). Three more that are easy to find in a shop and built to the same pattern: the Vortex Defender XL (opticsforce.com), the EOTech EFLX (riflesupply.com) and the Bushnell RXS-10 (bushnell.com).

Pattern and dimensions

What this dataset publishes for the DeltaPoint Pro pattern today:

PropertyValueSource
Mounting styleScrew-throughdataset
Mounting screws2, described as M4 oval-head Torxthird-party footprint guides, below
Recoil sockets4, at the cornersdataset
Body lengthApproximately 46mmthird-party footprint guides, below
Footprint familyLeupold DeltaPoint Prodataset
Optics recorded on this pattern16 pages covering 17 SKUs from 5 brandsdataset
Pistols cut for it from the factory23 of 223, 17 of them SIG P320 modelssigsauer.com
Pistols reaching it through a plate107, across 20 of the 31 plate systems, 5 of them also cut for it directlydataset

The screw description and the 46mm figure trace to footprint guides, not to a Leupold drawing (optics-trade.eu, opticsplanet.com). Screw centre spacing, thread depth, socket diameter and window size are not published here. No window dimension is recorded for any of the 16 optics on this pattern, and no manufacturer drawing carrying those figures has been read into the dataset. The rule on this site is to print a null rather than a guess, so use the screws that shipped with your optic and the length its maker specifies for your slide.

Look-alikes that will not interchange

DPP against RMSc. The pattern pair most often treated as one. Same two screws, same four corner sockets, different size class: the RMSc record in this dataset states outright that the pattern exists at about 40mm for micro optics and about 46mm for full size ones, and that a slide cut for one length will not take the other. DPP is the 46mm end. The practical consequence is in the counts: 81 of the 223 pistols here are cut for RMSc at the factory against 23 for DPP, and 17 of those 23 are one pistol family, the SIG P320, because the industry mills the micro version onto carry slides. The RMSc hub carries that side.

The Shield RMS, specifically. It shares the screw and socket pattern at the larger size, but its locating posts are recorded as about 0.4mm undersized, so it seats loose rather than drop-in (shieldsights.com). This dataset files every Shield Sights optic under RMSc and records no DPP fit for any of them. Treat a loose-but-close fit as a maintenance problem, not a mount.

DPP against Docter or Noblex. Two screws and four corner sockets on both, and this dataset publishes no socket spacing for either, so there is no counting test that separates them. Say that plainly rather than pretend otherwise: match the optic against its own maker’s spec page. The line runs straight through product families, which is how people get caught. The Vortex Venom is recorded on the Docter pattern (egwguns.com) while the Venom Enclosed is recorded on DPP (dnwoutdoors.com). The Crimson Trace CTS-1250 is Docter here too, on Crimson Trace’s own page (crimsontrace.com). The Docter hub carries the 6 optics on that pattern.

DPP against RMR. Four corner sockets against two forward bosses, which is a clean test in both directions. The RMR hub carries 35 optics against 16 here, and 18 factory-cut pistols against 23, 17 of those 23 SIG P320s. Outside the P320 line both patterns are plate-dependent in practice, and a slide that takes one rarely takes the other: only the SIG P385, the two CZ DUTY models, the Ruger RXM and the Shadow Systems MR920 accept both directly.

DPP against the Holosun K pattern. Different count and different size class: Holosun K is a two-screw, two-lug carry pattern with 6 optics and 21 factory-cut pistols. Nothing on that list mounts here, though the two CZ DUTY slides take both patterns directly.

DPP against MOS, OSP, VIS, AOS, LOPMS and the rest. Those are plate systems, not footprints. A slide stamped MOS or OSP has no footprint milled into it at all: the plate decides. See Glock MOS and the plate section on this page.

A disagreement that has now been settled. Until 2026-10-04 the pattern description printed above the tables on this page listed parts the industry associates with the DeltaPoint Pro cut, including a Sig Romeo1Pro and a Holosun SCS 320. This dataset holds no optic page for an SCS 320 at all and its Romeo1Pro row carries no footprint, and where the dataset does hold a page the page’s own sourced footprint governs: the CTS-1250 is filed under Docter on Crimson Trace’s own product page, and the Holosun SCS pages here are built for a specific maker’s plate pocket rather than this pattern. The description now names only optics this dataset files here, and keeps the Shield RMS and Docter as look-alikes rather than members. The rule behind the edit has not changed: a reputation is not a fit, and if an optic is not in the list on this page, this site is not claiming it mounts here.

How a plate gets you to DPP

23 pistols in this dataset are cut for the DeltaPoint Pro at the factory: the 17 SIG P320 models, whose PRO cut SIG describes as “a SIG SAUER Electro-Optics ROMEO1PRO and Delta Point Pro footprint” (sigsauer.com), plus the SIG P385, the CZ DUTY 4.0 C and 4.0 F, the FN 309 MRD, the Ruger RXM and the Shadow Systems MR920. 107 take a DPP optic through a plate, and the two groups overlap by 5 P320s, the ones Outer Impact names for its M.R.A. plate, which have both routes. Counted once each, 125 of the 223 pistols here, or 56.1 percent, can carry one of these optics one way or the other.

In words, a plate path works like this. The slide is milled for a proprietary interface that is not a footprint at all. A plate drops into that interface and its top face carries a real footprint. Fit the plate that presents DPP and the slide behaves, for optic-buying purposes, like a DPP slide. The plate table for each system lives on that system’s own hub, not here.

Most plate systems in this dataset offer a DeltaPoint Pro path. 20 of the 31, covering 13 pistol brands. The 11 without one are narrower plate sets: the Kimber 2K11 system, whose only recorded plate presents RMR, the C&H plates for the SIG P320 and the CZ Shadow 2 OR, Beretta’s APX A1 Carry and 80X kits and its 90-Series ACRO kit, HK’s VP9A1 plates (HK’s plate 04 is listed for the “Leupold DeltaPoint”, which is not recorded as the DeltaPoint Pro pattern) and its VP9CC plates, which HK lists for the Holosun 507K, Shield RMSc and Trijicon RMRcc only, and the Canik TTI Combat, TP9 Elite Combat and Kimber KDS9c plates. RMR has a path on 25 of the 31. It is still a strong argument for this footprint: on most optics-ready pistols a reader already owns, the plate exists. The largest paths, by pistol count:

Eleven further systems present DPP on 5 pistols or fewer: CZ P-10 OR and HK VP9 OR (chpws.com), Canik METE (outerimpact.com), Canik SFx Rival (canik.com), Beretta APX A1 (beretta.com), Glock Gen6 OR (us.glock.com), Springfield XD Mod.4 OSP, Springfield XD OSP (store.springfield-armory.com), Staccato HD HOST (staccato2011.com), Springfield AOS (springfield-armory.com) and the Ruger factory plate (outerimpact.com). Every path and its pistol list is in the plate section further down this page.

Two costs come with a plate: height above the bore, and one more interface that can loosen under recoil. This dataset records no DPP-pattern optic that ships with its own adapter plate in the box, so on a plate-system pistol the plate is a separate purchase. If your slide is cut for DPP directly, that is the better mount.

How to choose a DeltaPoint Pro optic

No prices on this page and no rankings the data cannot support. The live offer links beside each optic in the list below carry current pricing; the copy here does not, because a number written into prose is wrong within a week. What the data does support:

Provenance, stated plainly: 16 of the 16 optic pages on this pattern have been verified against a manufacturer page, part of 112 of the 112 optic pages site-wide. One of them is the DeltaPoint Pro itself, verified on 2026-10-04 because the pattern is named for it and the row cites Leupold’s own page for that exact model. The footprint record itself still rests on three third-party footprint guides rather than a Leupold specification document. Nothing here is verified against a physical sample. Confirm against your own slide before you spend money.

Where to go next

Optics with the DPP footprint · 16

Pistols cut for the DPP directly · 23

Mount it with a plate

Beretta APX A1 · 2 pistols

Via the Beretta APX A1 plate kit (DPP). beretta.com

Show the 2 pistols
All 2 pistols with the Beretta APX A1 plate system

Canik METE · 1 pistol

Via the Outer Impact Canik METE M.R.A. (DPP) plate. outerimpact.com

Show the 1 pistol
All 1 pistol with the Canik METE plate system

Canik SFx Rival · 2 pistols

Via the Canik SFx Rival optic plate (DPP). canik.comcanik.com

Show the 2 pistols
All 2 pistols with the Canik SFx Rival plate system

Glock Gen6 OR · 3 pistols

Via the Glock Gen6 OR plate 04 (DPP). us.glock.com

Show the 3 pistols
All 3 pistols with the Glock Gen6 OR plate system

Ruger factory plate · 1 pistol

Via the OEM/Aftermarket Ruger factory optic adapter plate system optic plate (DPP). outerimpact.com

Show the 1 pistol
All 1 pistol with the Ruger factory plate

Springfield XD Mod.4 OSP · 1 pistol

Via the Springfield Armory XD Mod.4 OSP plate (DPP). springfield-armory.comstore.springfield-armory.com

Show the 1 pistol
All 1 pistol with the Springfield XD Mod.4 OSP plate system

Walther PDP 1.0 · 1 pistol

Via the Walther PDP Gen 1 Optic Plate (DPP). waltherarms.comoptics-spot.com

Show the 1 pistol
All 1 pistol with the Walther PDP 1.0 plate system

Frequently asked

What optics use the DPP footprint?

16 optics use the DPP footprint, including the Bushnell RXE-MR1, Bushnell RXS-10, Bushnell RXS-100 and Bushnell RXS-250.

How is the DPP footprint mounted?

The DPP footprint uses 2 screws and a screw through mounting style. It also incorporates 4 recoil lugs to resist rearward movement under firing.

Is the DPP footprint part of a larger family?

The DPP footprint is part of the Leupold DeltaPoint Pro family. Optics and adapter plates within the same family often share compatible mounting dimensions, which can expand which pistols and adapter solutions are available.

Which pistols take the DPP with a plate?

107 pistols reach the DPP through an adapter plate, using the Beretta 90-Series, Beretta APX A1, CZ P-10 OR, Canik METE and 16 more plate systems.

What is the DeltaPoint Pro footprint?

It is the mounting pattern Leupold introduced with the DeltaPoint Pro: two screws that pass down through the optic body into the slide, and four recoil sockets at the corners of the optic base, on a body roughly 46mm long. 16 optic pages in this dataset, covering 17 SKUs from 5 brands, are built to it. 23 of the 223 pistols here are milled for it at the factory, 17 of them SIG P320 models, and on most other pistols it arrives through a plate.

What is the difference between the DPP and RMSc footprints?

Size, not shape. Both patterns use two screws and four corner recoil sockets, so counting will not separate them. The RMSc pattern exists at two body lengths, about 40mm for micro optics and about 46mm for full size ones, and DPP is the 46mm end of that family. This dataset keeps them as separate footprints with no cross fit recorded in either direction: 16 optics and 23 factory-cut pistols on DPP against 34 optics and 81 factory-cut pistols on RMSc.

Will a DeltaPoint Pro fit a Glock?

Not on a factory-cut Glock slide, and not without a plate. No Glock in this dataset is milled for the DPP pattern. 15 Glock MOS pistols reach it through Glock's own MOS adapter plate 04 (08 on the wider slides), which Glock lists for Leupold and EOTech optics, and the 3 Glock Gen6 pistols through plate 04 of Glock's separate Gen6 OR set, listed for the Leupold DPP. MOS is a plate system, not a footprint, so the plate you fit decides which optics mount.

Which pistols come cut for the DeltaPoint Pro from the factory?

23 of 223: the 17 SIG P320 models, whose optic cut SIG lists as PRO and describes as a ROMEO1PRO and DeltaPoint Pro footprint (sigsauer.com), plus the SIG P385, the CZ DUTY 4.0 C and 4.0 F, the FN 309 MRD, the Ruger RXM and the Shadow Systems MR920. The P385, the two DUTY models, the RXM and the MR920 accept more than one footprint directly; the 309 MRD is recorded on DPP alone. Five of the P320s also take Outer Impact's DPP plate. The other 102 pistols here that can carry a DPP optic do it only through an adapter plate.

Is the DPP footprint the same as the Docter cut?

No, and this is the mix-up counting cannot settle. This dataset records two screws and four corner sockets for both patterns and publishes no socket spacing for either, so the only reliable check is the optic maker's own spec page. The split runs inside single product lines: the Vortex Venom is recorded on the Docter pattern and the Venom Enclosed on DPP.

Which enclosed emitter red dots use the DeltaPoint Pro footprint?

Five of the 16: the Bushnell RXE-MR1, the EOTech EFLX CE, the Sig Sauer Romeo-X Enclosed Pro, the Vortex Defender-ST Enclosed Solar and the Vortex Venom Enclosed. That is a third of the pattern, the highest enclosed share of the three large footprints here, against 4 of 35 on RMR and 10 of 34 on RMSc.