FN 509 optic footprint and plates
The FN 509 is a plate system, not an optic footprint. 12 pistols use it, and its plates present the ACRO, DPP, Holosun 509T, Holosun K and RMR footprints.
FN's Low-Profile Optics Mounting System is one plate interface shared by the 509, 510 and 545 slides, so a plate bought for one fits the others. C&H Precision plates for it present the RMR, DeltaPoint Pro, ACRO, Holosun K (407K/507K, plus a separate plate for the EPS and EPS Carry) and Holosun 509T patterns.
Plate system
FN 509
- Family:
- FN 509 / Low-Profile Optics Mounting System plate system
- Screw count:
- not recorded
- Mounting:
- proprietary_plate
- Optics:
- 0
- Pistols:
- 12
Footprint specifications are compiled from manufacturer drawings and optic spec sheets.
What is in the slide pocket, and how to read the number on your plate
The useful question on an FN is never which footprint the slide has. It is which part is sitting in the pocket, because that part carries the footprint and it has a number.
FN numbers the plates, and the number is the answer. FN’s parts catalogue runs plates 501 to 504 and inserts 505 to 507, each pairing with one optic family: plate 501 is the DeltaPoint Pro plate (midwestgunworks.com), 502 the Trijicon RMR plate (midwestgunworks.com), 503 the plate listed for Docter, Burris and Vortex Venom and Viper sights (midwestgunworks.com), and 504 the plate listed for the Vortex Razor and the C-More STS2 (midwestgunworks.com). If you can read a number off the part you already own, you are done: that number names the pattern, and the pattern names the optics. No measuring, no guessing from the slide.
It is three parts per optic, not one. This is the thing that catches people buying loose plates. FN’s own optics mounting setup guide pairs each optic with a plate, an insert and a screw set, so the chart reads as a row rather than as a single part number: a Trijicon RMR takes plate 502, insert 506 and screw set 511, while a Docter, Burris or Vortex Venom and Viper sight takes plate 503 with insert 507 (midwestgunworks.com). FN sells the three together, and its store describes a Low-Profile Optics Mounting System kit as containing an MRD plate, an insert and mounting screws (fnestore.com). Buy the kit. A plate on its own can leave you a part short on install day.
The Aimpoint path stacks rather than swapping. FN’s ACRO adapter is not a fifth plate in that numbering: FN’s store sells it as a mounting plate for the Low-Profile Optics Mounting System on the 509, 510 and 545, and it goes on with the MRD plate and its own screws rather than instead of them (fnestore.com). In FN’s own chart the ACRO shares plate 501 with the DeltaPoint Pro and takes screw set 515. If you are shopping FN’s ACRO route, budget for both parts. C&H Precision sells a one-piece ACRO plate for the same pocket instead.
A pistol with no optic is not empty. The same pocket takes a blank slide cap, and it is a separate part from the plates above. So “there is a metal part under my optic” and “there is a metal part where my optic would go” are both normal on this platform, and neither tells you which pattern you have. Only the number does. The wider question of how an FN plate pocket differs from a milled slide is worked through in the FN 509 optic plate guide, which this page does not repeat.
FN’s own parts catalogue names patterns this dataset does not record
This is the most important paragraph on the page, and it is an argument against our own numbers.
This dataset records 5 plate paths for the system: RMR, DeltaPoint Pro, Holosun K, ACRO and Holosun 509T, all 5 traced to C&H Precision’s own plate listings for the 509, 510 and 545 (chpws.com). C&H is the maker of those plates, so its listing is first party about them, but it is not FN. FN’s own store describes the system as accepting major optic footprints “including the Trijicon RMR, Docter/Noblex, C-More, RMS/c, and Aimpoint Acro” with an adapter plate, and lists kits for the Leupold DeltaPoint Pro, the Vortex Razor, the Vortex Venom/Viper/Docter/Burris group and the Trijicon RMR (fnestore.com). Read the two lists side by side and FN names three patterns no recorded plate presents: RMSc, Docter and C-More STS, the last of them as plate 504 for the Vortex Razor and C-More STS2 (midwestgunworks.com).
What this page will and will not say about that. It will not say a Vortex Venom or a Shield RMSc fits an FN, because this dataset has not verified an FN plate for either pattern and a fit claim here comes from the data or not at all. It will say, plainly, that the 5 paths are probably an undercount of FN’s parts bin rather than a complete picture of it, that the specific parts to verify are plates 503 and 504 and FN’s RMS/c route, and that a reader holding one of those sights should ask FN or the plate seller rather than read our silence as a no.
What the three would be worth, in pages. Today the 12 pistols on this system each reach 66 of the 112 optic pages here. Add the 34 RMSc pages and it becomes 100. Add the 6 Docter pages and it becomes 106, and the single C-More STS page takes it to 107, which is above every pistol in this dataset, whose ceiling is 101 today. Without the RMSc route, Docter and C-More alone take it only to 73, with 55 pistols here still above it. The RMSc question is the one worth answering first.
Why the Docter half still matters. Those 6 pages are 4 brands and 6 sellable variants, 6 of the 6 are flagged verified here, and they are the mid-market open-emitter sights people already own. Of the 31 plate systems in this dataset, 18 carry a Docter plate and 13 do not, and the 13 without it cover 59 pistols between them. 36 of those sit on this system and the three other C&H plate families that present the same 5 patterns, S&W M&P CORE, CZ P-10 OR and HK VP9 OR. The rest include the 3 pistols on the Glock Gen6 OR plates, the 5 on the Staccato HD HOST kit and the 2 on the Kimber 2K11 kit. If the FN plate is real and simply unrecorded here, the same question is worth asking of the other C&H families.
Pattern and dimensions, and the numbers nobody publishes
What this dataset publishes for the FN system, and what FN publishes about the parts that go in it:
| Property | Value | Source |
|---|---|---|
| Kind | Plate system, not a footprint | dataset |
| Mounting style | Proprietary plate | dataset |
| Plate retention screws | 2, started by hand, T10 Torx key supplied with the pistol | midwestgunworks.com |
| Recommended screw torque | 22 inch-pounds, no threadlocker | midwestgunworks.com |
| Parts per optic | A plate (501 to 504), an insert (505 to 507) and a screw set (510 to 515) | fnestore.com |
| Sealing | An o-ring sits under the plate and is removed and refitted with it | midwestgunworks.com |
| Screw spacing, boss layout, pocket depth, plate thickness | Not published, here or by FN | dataset |
| Pistols on the system | 12 of 223 | fnamerica.com |
| Plate paths recorded | 5, presenting RMR, DeltaPoint Pro, Holosun K, ACRO and Holosun 509T | chpws.com |
| Optics that mount with no plate | 0 | dataset |
Three of those rows need reading carefully.
The chips at the top of this page say “Screw count: not recorded”, and that wording is deliberate. It is not a zero and it is not a measurement. A plate system has no screw count of its own, because each plate carries its own fasteners and FN’s chart gives a different screw set per optic. 28 of the 31 plate systems in this dataset print “not recorded” here for exactly that reason, and a 0 sitting in that chip would read as a count somebody took. Where you do see a 0 on this site it is sourced: the Holosun 509T clamp genuinely takes no top-down screws.
No geometry is published, by us or by FN. Screw spacing, boss layout, pocket depth and plate thickness are absent from this record, and FN’s pistol pages describe the system in prose rather than in dimensions. The one mechanical figure FN does publish about the interface is the patent number: its 509 Tactical page credits “U.S Patent No. 10/352,654 Low-Profile Optics Mounting System that enables the platform to accept more than ten commercially-available miniature red dot (MRD) optics” (fnamerica.com). Measuring your own slide gets you a number with nothing to compare it against, which is why the instruction on this platform is always to read the part number.
The o-ring is the part people lose. FN’s setup sequence has you lift the optic or slide cap, the plate and the o-ring out together, clean the mounting surface, then refit the o-ring before the plate (midwestgunworks.com). It is the one part of this interface no other plate system on the site records, and it goes back in under the plate, not on top of it.
Look-alikes that will not interchange
FN’s plate numbers against FN’s pistol names. The sharpest trap on this platform is that FN uses the same small numbers for both. Plate 502 is the RMR plate and plate 503 is the Docter plate, while FN’s pistol line runs numbers in the same range that have nothing to do with this system: an aftermarket mount for this slide states outright that it “DOES NOT FIT THE FN 502, FN 503, or FN 5.7” (apextactical.com). This dataset holds 15 FN pistols, level with Canik as the fifth largest catalogue here after Sig Sauer, Springfield Armory, Smith & Wesson and Glock, and every one of them but one is a 509, 510, 545 or Reflex. The exception is the 309 MRD, covered below. A search result reading “FN 503” may be a pistol or a plate, so check which before you buy.
The Reflex pair against everything else FN sells. The two Reflex models are milled for RMSc and Holosun K directly, take no plate at all, and reach 40 optic pages where a 509 reaches 66. The two sets share the 6 K pages and nothing else: a Reflex reaches the 34 RMSc pages a 509 cannot, and a 509 reaches the RMR, DeltaPoint Pro, ACRO and 509T pages a Reflex cannot. The 309 MRD is the other FN here that takes no plate: FN describes a direct-mount slide, and this dataset records it as cut for the DeltaPoint Pro directly, reaching the 16 DPP optic pages and nothing else. The full intra-brand comparison is in the plate guide; the identification rule is the short version: badge says Reflex or 309, there is no plate.
The RMR plate against the Holosun K plate. Both patterns record 2 screws and 2 front lugs in this dataset and differ by body size: RMR is a full size pattern, K a micro one. No hole count separates them, so match the pattern your optic’s own spec page names and never count sockets on this pair.
The DeltaPoint Pro plate against an RMSc or Docter optic. DPP, RMSc and Docter all record 2 screws and 4 corner sockets, a three-way tie that hole counting cannot resolve (opticsplanet.com). On this platform only the DeltaPoint Pro is recorded, so an RMSc or Docter sight that seems to line up with the DPP plate’s holes is not recorded as fitting it.
The ACRO plate against the Holosun 509T plate. Both clamp rather than bolt through, and they are separate plates here. An ACRO interface has no top-down screw holes at all: one cross-bolt clamps the sight onto a dovetail with a recoil stopper in a slot (optics-trade.eu). The 509T clamp has its own dimensions and its own C&H plate, “FN 509, FN 510, and FN 545 V4 MIL / LEO to Holosun 509T (STEEL)”.
A plate advertised as “RMSc / 507K”. Aftermarket mounts for this slide are sold under both names at once, including an RMSc mount listed for the 507K (apextactical.com). C&H’s own small-optic plate names the 407k and 507k, and this dataset tracks Holosun K as its own pattern, the K cut being the RMSc screw and front lug layout with the rear lugs deleted (opticsplanet.com), so it records that plate as K and claims no RMSc fit on any 509. Treat a dual-named listing as a question for the seller, not as a confirmed pattern.
Another system’s plate. Every plate system here is cut for its own pocket and none of their plates swap. Glock MOS, SIG P320 C&H, S&W M&P CORE, Canik METE, CZ P-10 OR, HK VP9 OR, Beretta APX A1, Springfield XD OSP, Springfield AOS, Springfield Echelon VIS, Taurus TORO, Ruger factory optic plate, Walther PDP 1.0 and Walther PDP 2.0 each have their own. 3 other systems in this dataset present exactly the same 5 patterns as this one, being the C&H plates for the S&W M&P CORE, CZ P-10 OR and HK VP9 OR, and not one of their plates will drop into an FN pocket. What travels between platforms is the optic, never the plate.
How a plate gets you to a footprint
In words: the slide is machined for a rectangular pocket. An o-ring goes in, a numbered plate goes on top of it, an optic-specific insert goes with the plate, and 2 screws hold the stack down. The plate’s top face carries a real optic footprint, so fit the RMR plate and the pistol behaves, for shopping purposes, like an RMR pistol. Fit the K plate and the same slide behaves like a K pistol. Nothing about the gun changed; the interface on top of it did.
The 5 paths recorded here, and the thing each one is the only route to:
- The RMR plate (FN 502, or C&H’s RMR plate): 35 RMR optics from 8 brands across 49 variants. The longest list on this pistol, the deepest variant pool, and the sole route to Trijicon, Swampfox, Meprolight, Primary Arms, Riton and Canik.
- The DeltaPoint Pro plate (FN 501): 16 DPP optics from 5 brands, a third of them enclosed, and the sole route to Leupold, EOTech, Sig Sauer and Vortex.
- The Holosun K plate: 6 Holosun K optics, all Holosun, across 17 variants, 4 of them enclosed. C&H sells the 407K and 507K plate and a separate EPS and EPS Carry plate; both present K here. It is also the pattern that carries over to an FN Reflex, which is worth something if you expect to own both.
- The ACRO plate, or FN’s adapter on plate 501: 7 ACRO optics from 4 brands, all 7 enclosed, and the sole route to Aimpoint, Steiner, Burris and Colt Optics on this pistol. The one Aimpoint page not on this pattern, the COA, sits on A-CUT, which no plate presents. 19 of the 31 plate systems here have no ACRO path at all, so this is a real advantage of the FN pocket over several higher-scoring ones.
- The Holosun 509T plate: 2 Holosun 509T optics, both enclosed, across 8 variants.
Those 5 lists do not overlap: no optic page in this dataset sits on two FN paths, which is why 35 plus 16 plus 6 plus 7 plus 2 lands on exactly 66 with nothing double counted. The flip side is the part people underestimate. Whichever plate goes on the gun removes at least 31 of those 66 pages from consideration before you have looked at a reticle, and on the 509T route it removes 64. Choose the optic, then let it name the plate.
What the fitment lines name that this site cannot show you
66 of 112 is a floor on this site, not a ceiling on the market, and the system’s own cited source is where you can see that.
The C&H Precision fitment page the 5 paths come from lists each plate by the sights it takes, and those lists include optics that have no page here at all: Olight Osight X and Osight S, and C&H’s own EDC, EDC Enclosed, EDC-XL, COMP, COMP MAX, DUTY and DUTY-XL sights (chpws.com). Neither Olight nor C&H is among the 19 optic brands in this dataset, so 9 optic models named on the very page that establishes this system’s plates produce nothing on this site. The same page is the reason all 12 pistols are modelled as one mounting population, listing a single plate part to the “FN 509, FN 510, FN 545 V4 MIL / LEO” (chpws.com).
The honest reading of our own headline number, then, is this: 66 is every optic page on this site that an FN can be shown to reach, 98 of the 151 sellable variants behind those pages, 16 of the 19 brands, and 66 of the 112 verified pages. The two brands out of reach are Shield Sights and Crimson Trace, whose pages here sit on RMSc or Docter. It is not a count of every red dot that will bolt to an FN plate, and no number on a site with 112 optic pages could be.
How to choose a plate and an optic
No prices on this page, and no rankings the data cannot support. What the data does support:
- Choose the optic first, then buy the kit it names. The plate is a consequence of the sight, not a preference, and FN’s chart hands you the plate, insert and screw numbers once the optic is decided.
- Buy the kit, not the plate. A kit is a plate, an insert and screws (fnestore.com). A loose plate off a marketplace listing can arrive without the insert the chart pairs it with.
- Widest choice: the RMR plate. 35 pages, more than the other four paths put together, and 49 variants.
- Enclosed emitter: 22 of the 34 enclosed sights here are reachable, and they arrive across all 5 plates. If a sealed emitter is the requirement, start from the optic.
- If the requirement is an Aimpoint, the ACRO route is the only one, and on FN’s own parts it is a two-part purchase: the MRD plate plus the ACRO adapter and its screws.
- Use the screws that come with the plate. FN’s setup guide gives 22 inch-pounds and no threadlocker, and the screws in your optic box were sized for a slide with no plate under the sight.
- If you already own a Docter or an RMSc pattern sight, ask before you give up on it. This dataset records no path, FN’s own store and catalogue name both patterns, and that gap is unresolved rather than decided. It is the one open question on this platform where the answer changes what you buy.
- If you already own a 407K or 507K, buy the C&H K plate. That is the one plate here named for it.
- If you want the shortest route to the most optics and you are still choosing a pistol, note that an FN sits above the median of this dataset rather than at the top: the median optic reach across all 223 pistols here is 58, 60 pistols reach more than 66 and 127 reach fewer. The 36 pistols on exactly 66 are these 12 and the 14 S&W M&P CORE, 5 CZ P-10 OR and 5 HK VP9 OR models, all four systems presenting the same 5 C&H patterns.
Nothing on this page is verified against a physical sample. Every fit claim is sourced research, and 112 of the 112 optic pages on this site carry a verified flag meaning the pattern was checked against the maker’s own page. Confirm against your own pistol before you spend money.
The open questions on this system, ranked by what they are worth
- FN’s RMS/c route. Worth 34 optic pages and the two brands this pistol cannot reach today. FN’s store names “RMS/c” among the footprints the system accepts; no plate in this dataset presents RMSc on it. Settling it is one first-party document.
- The Docter plate, part 503. Worth 6 optic pages, 4 brands and 6 verified rows. A retailer lists it as an FN factory part; this dataset has no Docter path for the system.
- The C-More plate, part 504. Worth 1 page. 9 of the 31 plate systems here present C-More STS today.
- No FN parts document is in our provenance yet. All 5 plate rows rest on C&H’s plate listings. The 2 FN pistol pages recorded against this system name the interface and its patent but not one footprint, which is the gap every item above shares.
Where to go next
- The full chart: all 42 optic footprints and plate systems.
- The post that owns this cluster, with the plate table, the intra-brand split and the optics an FN cannot reach: FN 509 optic plate guide.
- Why a plate is needed at all: do you need an adapter plate?
- The two patterns most FN buyers choose between: RMR footprint guide and Holosun K vs RMSc.
- The pattern at the centre of this system’s open questions: RMSc footprint guide and Docter footprint vs RMR.
- The only route to Aimpoint on this pistol: ACRO footprint guide.
- The longer body class on the DeltaPoint Pro plate: DeltaPoint Pro footprint guide.
- Pistols on this system: 509 Tactical, 509 Fullsize MRD, 509 Compact MRD, 509 CC Edge, 510 Tactical, 545 MRD.
- The FN pistols that need no plate: Reflex MRD and Reflex XL MRD.
- The same problem on other pistols: Glock MOS, S&W M&P CORE, CZ P-10 OR, HK VP9 OR.
Pistols with the FN 509 system · 12
- FN America 509 CC Edge
- FN America 509 Compact MRD
- FN America 509 Compact Tactical
- FN America 509 Fullsize MRD
- FN America 509 LS Edge
- FN America 509 Midsize MRD
- FN America 509 Midsize Tactical
- FN America 509 Tactical
- FN America 510 MRD
- FN America 510 Tactical
- FN America 545 MRD
- FN America 545 Tactical
No pistols match your filter.
Plates available
| Presents | Plate | Sources | Optics that fit |
|---|---|---|---|
| ACRO | C&H Precision FN 509 plate (ACRO) | chpws.com | 7 optics |
| DPP | C&H Precision FN 509 plate (DPP) | chpws.com | 16 optics |
| Holosun 509T | C&H Precision FN 509 plate (Holosun 509T) | chpws.com | 2 optics |
| Holosun K | C&H Precision FN 509 plate (Holosun K) | chpws.comchpws.com | 6 optics |
| RMR | C&H Precision FN 509 plate (RMR) | chpws.com | 35 optics |
Frequently asked
Which pistols use the FN 509 system?
12 pistols use the FN 509 plate system, including the FN America 509 CC Edge, FN America 509 Compact MRD, FN America 509 Compact Tactical and FN America 509 Fullsize MRD.
Which optics fit the FN 509?
Its plates present the ACRO footprint (7 optics), DPP footprint (16 optics), Holosun 509T footprint (2 optics), Holosun K footprint (6 optics) and RMR footprint (35 optics). Pick the plate for the footprint your optic uses.
Do I need a plate?
Yes. The FN 509 does not take an optic directly. Fit one of its plates: C&H Precision FN 509 plate (ACRO), C&H Precision FN 509 plate (DPP), C&H Precision FN 509 plate (Holosun 509T), C&H Precision FN 509 plate (Holosun K) and 1 more.
What is the FN 509 optic footprint?
There is no FN 509 footprint. The slide carries a pocket for FN's Low-Profile Optics Mounting System, and the plate you drop into that pocket is what presents a real footprint to the optic. All 12 FN pistols on the system in this dataset, across the 509, 510 and 545 lines, work that way, and none of them takes an optic with no plate. The 5 plate paths recorded here are C&H Precision plates presenting the RMR pattern (35 optic pages), DeltaPoint Pro (16), Holosun K (6), ACRO (7) and Holosun 509T (2), which is 66 pages in total with nothing counted twice.
How do I tell which FN MRD plate I already have?
Read the number FN assigns it rather than measuring the slide. FN's parts catalogue numbers the plates 501 to 504 and the inserts 505 to 507: plate 501 is the DeltaPoint Pro plate and the base the Aimpoint ACRO adapter sits on, 502 is the Trijicon RMR plate, 503 is listed for Docter, Burris and Vortex Venom and Viper sights, and 504 is listed for the Vortex Razor and C-More STS2. A pistol stored with no optic usually carries the blank slide cap in the same pocket instead.
What is the difference between an FN MRD plate and an MRD insert?
The plate is the part that drops into the slide pocket and carries the footprint on its top face. The insert is a smaller optic-specific piece that goes with it, and FN's own setup chart pairs each optic with a plate, an insert and a screw set rather than with a plate alone. That is why buying a loose plate off a marketplace listing can still leave you a part short, and why FN sells the three together as a kit.
How tight should the FN 509 optic plate screws be?
FN's own optics mounting setup guide gives a recommended torque of 22 inch-pounds and tells you not to use threadlocker on them, with both screws started by hand first using the T10 Torx key supplied with the pistol. The screw set is optic-specific in FN's chart, numbered 510 to 515, so the screws that came in your optic box were sized for a slide with no plate under the sight and should stay in the box.
Will a Vortex Venom or a Burris FastFire fit an FN 509?
This dataset records no Docter pattern plate for the FN system, so it claims no fit for the 6 Docter pattern optics, the Venom and Viper and the Burris FastFire 3 and 4 among them. That is a gap in these records rather than a settled no: FN's own parts catalogue lists an MRD plate numbered 503 for Docter, Burris and Vortex Venom and Viper sights. Until that part is verified against FN's own documentation and added here, this site stands behind the 5 paths it has sourced and nothing more. Ask FN or the plate seller before you buy the optic.
Will a Holosun 507K fit an FN 509?
Yes, through C&H Precision's plate. C&H lists "FN 509, FN 510, and FN 545 V4 MIL / LEO to Holosun 407k / 507k / Vortex Defender CCW / C&H EDC / EDC Enclosed / Olight Osight S", plus a separate plate for the Holosun EPS and EPS Carry, so this dataset records a Holosun K path for all 12 pistols, reaching the 6 K optic pages. That plate used to be filed here as an RMSc plate; C&H names it for the 407K and 507K.