Walther PDP 2.0 optic footprint and plates

The Walther PDP 2.0 is a plate system, not an optic footprint. 7 pistols use it, and its plates present the ACRO, DPP, Docter, Holosun 509T, RMR and RMSc footprints.

Walther PDP second-generation optic cut. Adds recoil bosses to the slide for improved direct-mount stability versus PDP 1.0. Still uses adapter plates for non-native footprints, but plate geometry is distinct from PDP 1.0.

Plate system

Walther PDP 2.0

Family:
Walther PDP
Screw count:
2
Mounting:
proprietary_plate
Optics:
1
Pistols:
7

Footprint specifications are compiled from manufacturer drawings and optic spec sheets.

How to identify a PDP Gen 2 optic cut without a caliper

The hard question on this platform is not which optic. It is which generation of PDP you are holding, because the two take different plates and nothing about the outside of the gun announces which one you have.

Walther’s own pistol listing will not tell you. This is the part worth knowing before you spend an evening on it. The waltherarms.com model pages this dataset records as provenance for these 7 pistols describe the interface only as a plate cut; not one of them names a generation. So reading the spec sheet for your exact model, the obvious first move, returns nothing useful.

The plate listing does tell you. Walther’s factory Gen 2 optic plate page states its own fitment in a line the pistol pages never carry: it “Fits PDP, F-Series, & Steel Frame variants with the Gen 2 Optic-Cut” (waltherarms.com). That is the generation question answered from the parts catalogue rather than from the gun catalogue, and it is the single most useful sentence on this platform.

Use the launch dates as a first filter. The retailer plate guide this dataset draws its plate list from dates the first optic cut to 2021 and the second to 2022 and later (optics-spot.com). A PDP bought new in 2021 is very likely Gen 1; a PDP Match, Pro SD, Steel Frame or F-Series Standard is recorded here as Gen 2. Date narrows it. The plate listing settles it.

Then look in the recess. Lift the plate out and look at the floor of the pocket. This dataset records 2 recoil bosses standing proud in the Gen 2 recess and 0 in the Gen 1 recess, which is the whole claimed mechanical difference between the generations: the bosses give the plate something to locate against under recoil instead of leaving the screws to carry the load (survivalstoic.com).

And here the honest limit arrives with the method. That boss count is not confirmed by any Walther document in this dataset. The record carrying it says so in its own notes: 2 is plausible from community reporting and wants a factory spec sheet before anyone treats it as measured. So use the bosses to confirm what the plate listing already told you, never as the primary test, and do not file or shim anything on the strength of a number this site has flagged as unverified.

One more thing the dataset will not do for you. 7 Gen 2 pistols sit on this system here against 1 Gen 1 pistol, and that split is about sourcing rather than about how many of each Walther sold. Every one of the 7 Gen 2 rows cites a waltherarms.com page. The single Gen 1 row rests on a third-party footprint round-up. Do not read 7 against 1 as a statement about the installed base.

The one optic that bolts to the slide, and what it is worth

Across the 31 plate systems in this dataset, 26 record no optic that mounts without a plate. 2 record exactly one each, and both of those are a Holosun SCS, a sight built for one maker’s slide pocket rather than to any optic footprint. The two SIG P320 records and the Canik METE record are the cases apart: SIG describes the P320 cut as a DeltaPoint Pro footprint and Canik cuts the METE SFx PRO for Shield RMSc, so their pistols take optics directly through a footprint rather than through the plate system. On this platform that optic is the Holosun SCS-PDP-GR, recorded as a direct fit on all 7 Gen 2 pistols here and sourced to Holosun’s own product page (holosun.com). The RMR record on this site spells out why it is filed here rather than on a footprint: Holosun’s SCS models “are not on this pattern: each is cut for one maker’s plate pocket”.

That one row is doing more work than its size suggests.

It keeps a Gen 2 PDP at the top of this dataset. Counting its 6 plate paths plus the optic that needs no plate, a Gen 2 slide reaches 101 of the 112 optic pages here, from all 19 optic brands, across 129 of the 151 SKUs. Across all 223 pistols the median reach is 58. 11 pistols land on 101, the 7 Gen 2 models and 4 SIG P320s that carry both C&H Precision and Outer Impact plates; 212 pistols reach fewer and not one reaches more. The next tier is the 15 Glock MOS pistols on 100. Against the Gen 1 PDP, on 98, the gap is three pages wide: this optic, and the 2 Holosun 509T optics that no other PDP reaches, through the Gen 2 509T plate. Take this optic away and a Gen 2 PDP drops to 100, level with the MOS Glocks.

It is also a narrow claim, though a sourced one. The SCS-PDP-GR record carries two source URLs, both on holosun.com, is flagged verified, and publishes a 20 x 15 mm window. Today 112 of the 112 optic pages here carry a verified flag, and 101 of those sit among the 101 a Gen 2 PDP reaches. This particular row is one of the 112.

And the 2-of-31 figure is a gap in this dataset, not a fact about hardware. Holosun’s own catalogue, in URLs already recorded here, lists SCS models built for other makers’ slide pockets: the SCS-MP2-GR, the SCS-P10-GR and the SCS-VP9-GR. None of the three has a footprint attached in this dataset, so none produces a page and none appears in any count, which is part of why the S&W M&P CORE (14 pistols), CZ P-10 OR (5) and HK VP9 OR (5) hubs all read zero optics mounting without a plate. This page claims no fit for those three sights. It names them because a reader comparing platforms deserves to know that this platform’s lead is partly a record-keeping lead.

Pattern and dimensions

What this dataset publishes for the Walther PDP 2.0 system:

PropertyValueSource
KindPlate system, not a footprintdataset
Mounting styleProprietary platedataset
Plate retention screws2dataset
Recoil bosses in the slide recess2, unconfirmed by any Walther documentsurvivalstoic.com
Screw thread, screw spacing, boss spacingNot published heredataset
Recess dimensions and plate part numbersNot published heredataset
Pistols on the system7 of 223waltherarms.com
Plate paths recorded6, presenting RMR, RMSc, DeltaPoint Pro, Docter, ACRO and Holosun 509Toptics-spot.com, waltherarms.com
Footprints that source line names7optics-spot.com
Optics that mount with no plate1holosun.com

Two of those rows need reading carefully.

The summary chips at the top of this page say “Screw count: 2”. They show no recoil lug count, and this record is the only plate system of the 31 here that publishes one at all: 3 of the 31 publish a screw count; 1 publishes a boss count, and it is this one. The other 28 print “not recorded” rather than a number, and that wording is load-bearing. It is not that those systems have no fasteners and not that anyone measured a zero: nobody has recorded theirs. The field is left blank for exactly that reason, because a 0 sitting in a chip reads as a count somebody took, and mistaking a missing figure for a measured one is the single easiest way to misread the 42 hubs on this site.

The 2 screws and 2 bosses here are not an RMR pattern, even though RMR and Holosun K are the two true footprints in this dataset that also publish 2 and 2. Those numbers describe different objects. On RMR, the 2 screws pass through the optic body and the 2 lugs sit under it. Here the screws retain a plate and the bosses locate that plate, and the optic never touches either. Nothing is interchangeable on the strength of matching counts, which is why this record is filed as a plate system and not as a footprint.

Screw thread, screw spacing, boss spacing, recess depth and plate part numbers are not published here, for this record or for any of the 42. The rule on this site is to print a null rather than a guess, so none of those figures appears above. Read spacing off the plate maker’s own listing.

Look-alikes that will not interchange

The system against a footprint. There is no Walther PDP footprint. Nothing is cut to it, nothing is sold for it, and an optic advertised as fitting “the Walther PDP footprint” is either describing a plate or describing nothing.

A Gen 1 plate against a Gen 2 slide. The expensive one, and the reason this platform has 2 hubs instead of 1. Both records here state that the plate geometry differs between generations and that the two are not plate-interchangeable, which is why PDP 1.0 carries its own 5 plate rows presenting 5 of this system’s 6 patterns, every one except the 509T. The two hubs look nearly identical in their plate tables and the parts are not the same parts. A listing that says only “Walther PDP optic plate” has not told you what you need to know.

The RMSc plate against the DeltaPoint Pro plate. Both patterns record 2 screws and 4 corner sockets in this dataset, and they differ by body length: roughly 40mm for RMSc against roughly 46mm for DPP (badassoptic.com, optics-trade.eu). No hole count separates them. Match the pattern named on your optic’s own spec page and never count sockets on this pair.

The Docter plate against either of those. Docter is 2 screws and 4 corner sockets again (opticsplanet.com), so this platform offers three plates that are indistinguishable by hole counting. It is also the plate that catches used-market buyers: a Vortex Venom or Viper, a Burris FastFire or a Primary Arms SLx RS-10 is a Docter sight, and this is one of 18 of the 31 plate systems here that can take one.

The ACRO plate against all of them. The easy one. An ACRO interface has no top-down screw holes at all: a single cross-bolt clamps the sight onto a dovetail-style groove with a recoil stopper engaging a slot (optics-trade.eu). If the plate’s top face is a rail-like groove rather than a pair of screw holes, that is the ACRO plate. It is also the only route on this pistol to the 7 ACRO optics, every one of them an enclosed emitter.

A Holosun 509T against the ACRO plate. It clamps too and it is not cross-compatible. The 509T interface has its own dimensions, so the ACRO plate is not a general-purpose clamp mount. This system records a separate Gen 2 plate for the 509T instead (waltherarms.com), and it is one of 8 plate systems in this dataset with a path to that pattern, the Staccato HD HOST kit and C&H Precision’s 509T plates among the others. If the plate’s top face is a clamp groove, read the plate listing for which of the two it is.

The SCS built for a Glock against the SCS built for a PDP. Same product family, different slide pockets, and the model code is the only thing that separates them on a shelf. The SCS-M is recorded here on Glock MOS and fits 15 Glocks (holosun.com); the SCS-PDP is recorded on this system and fits these 7. Neither crosses over, and neither mounts on a plate.

Another system’s plate. Every plate system here is cut for its own recess and none of their plates swap. Glock MOS, SIG P320 C&H, S&W M&P CORE, Canik METE, FN 509, CZ P-10 OR, HK VP9 OR, Beretta APX A1, Springfield XD OSP, Springfield Echelon VIS, Taurus TORO, Staccato HD HOST and Kimber 2K11 each have their own. Three other plate systems in this dataset present the whole RMR, RMSc, DeltaPoint Pro, Docter and ACRO set this one does, the Gen 1 PDP, the Springfield Echelon VIS and Glock MOS, which adds a C-More plate. None of them adds a 509T plate, and not one of their plates will drop into a Gen 2 recess. What travels between platforms is the optic, never the plate.

How a plate gets you to a footprint

In words: the slide is machined for a recess with 2 bosses in it. A plate drops into that recess, is held by 2 screws, and its top face carries a real optic footprint. Fit the plate that presents RMR and the pistol behaves, for optic-shopping purposes, like an RMR pistol. Fit the RMSc plate instead and the same slide behaves like an RMSc pistol. Nothing about the gun changed; the interface on top of it did.

The 6 paths recorded here, and what each one opens:

Read those six lines together and the plate choice stops being about list length. Each of 4 plates is the only way to reach one or two makers on this pistol, and the other 2 reach no maker the rest cannot.

Those 6 groups do not overlap: no optic page appears on two of them, and the single direct-fit optic is on none of them. So the paths sum exactly to the 101 pages above, and whichever plate goes on the gun removes at least 66 of those 101 from consideration before you have looked at a reticle.

One sourcing limit shapes this whole section. 1 of the 6 Gen 2 plate paths, the RMSc one, traces only to a single retailer plate guide; the RMR, DeltaPoint Pro, Docter, ACRO and 509T plates are each sold on waltherarms.com, though none of those listings is a Walther technical document. And that retailer line names more plates than this dataset has recorded from it: it lists adapter plates for the “Trijicon RMR, Shield RMSc, Holosun K, Vortex Venom/Noblex (Docter), C-More RTS, Aimpoint Acro, and Leupold DPP” footprints, which is 7 patterns against the 5 of them recorded here. The 2 it has not attributed are Holosun K and C-More STS. The 509T is not on that line at all; its plate comes from Walther’s own catalogue. So 6 is the number this site will stand behind, not a claim that only 6 plates exist, and a reader holding a 507K should ask the plate maker rather than read this page as a no.

What a PDP 2.0 cannot mount

11 of the 112 optic pages here are out of reach of a Gen 2 PDP, and the shape of that list is the most interesting thing about it: 7 of the 11 are Holosun, and the other four are one page each from Primary Arms and Aimpoint and two from SIG Sauer. Every other brand in the dataset is fully reachable.

They fall into four groups:

Put the gap back and the arithmetic is striking. If the K and C-More plates that retailer line names were recorded here, a Gen 2 PDP would reach 108 of the 112 pages, and of the 4 still out of reach, 3 fit no pistol in this dataset at all. The only optic that fits a pistol and would still not fit a PDP is the Holosun SCS built for a Glock. That is why the K plate question deserves a reader’s time rather than a footnote.

How to choose a PDP plate and optic

No prices on this page and no rankings the data cannot support. What the data does support:

Nothing on this page is verified against a physical sample. Every fit claim is sourced research, a manufacturer or retailer page recorded against the record it supports, and no Walther plate drawing or slide spec is yet among those sources. Confirm against your own pistol before you spend money.

Where to go next

Optics with the Walther PDP 2.0 slide cut · 1

Pistols with the Walther PDP 2.0 system · 7

Plates available

Presents Plate Sources Optics that fit
ACRO Walther PDP Gen 2 Optic Plate (ACRO) waltherarms.com 7 optics
DPP Walther PDP Gen 2 Optic Plate (DPP) waltherarms.comoptics-spot.com 16 optics
Docter Walther PDP Gen 2 Optic Plate (Docter) waltherarms.comoptics-spot.com 6 optics
Holosun 509T Walther PDP Gen 2 Optic Plate (Holosun 509T) waltherarms.comwaltherarms.commidwestgunworks.com 2 optics
RMR Walther PDP Gen 2 Optic Plate (RMR) waltherarms.comoptics-spot.com 35 optics
RMSc Walther PDP Gen 2 Optic Plate (RMSc) optics-spot.com 34 optics

Frequently asked

Which pistols use the Walther PDP 2.0 system?

7 pistols use the Walther PDP 2.0 plate system, including the Walther PDP F-Series Standard 3.5", Walther PDP Match Full Size 5", Walther PDP Pro SD Compact 4.6" and Walther PDP Pro SD Full Size 5.1".

Which optics fit the Walther PDP 2.0?

Its plates present the ACRO footprint (7 optics), DPP footprint (16 optics), Docter footprint (6 optics), Holosun 509T footprint (2 optics), RMR footprint (35 optics) and RMSc footprint (34 optics). Pick the plate for the footprint your optic uses. 1 optic mounts on the Walther PDP 2.0 cut with no plate at all: the Holosun SCS-PDP-GR.

Do I need a plate?

For almost every optic, yes. The exception is the Holosun SCS-PDP-GR, built for the Walther PDP 2.0 cut itself. Everything else mounts through one of its plates: Walther PDP Gen 2 Optic Plate (ACRO), Walther PDP Gen 2 Optic Plate (DPP), Walther PDP Gen 2 Optic Plate (Docter), Walther PDP Gen 2 Optic Plate (Holosun 509T) and 2 more.

What is the Walther PDP 2.0 footprint?

There is no Walther PDP footprint to shop for, and that is why the searches end badly. The Gen 2 slide is machined for a plate, and the plate's top face carries the pattern an optic actually bolts to. The question that gets an answer is which plate. All 7 Gen 2 pistols in this dataset sit on the system, its 6 plates present the RMR, RMSc, DeltaPoint Pro, Docter, ACRO and Holosun 509T patterns, and those 6 paths plus the one optic built for the cut itself reach 101 of the 112 optic pages here, tied with four SIG P320 models for the most of any pistol in this dataset.

How do I tell a PDP Gen 1 cut from a PDP Gen 2 cut?

Not from Walther's pistol listing, which is the trap. The waltherarms.com model pages recorded here describe the interface only as a plate cut and never name a generation. The generation is written on the plate listing instead: Walther's factory Gen 2 ACRO plate page says it "Fits PDP, F-Series, & Steel Frame variants with the Gen 2 Optic-Cut". Use the date as a first filter, since the retailer guide this dataset draws its plate list from dates PDP 1.0 to 2021 and PDP 2.0 to 2022 and later, then confirm against the plate you intend to buy. This dataset records 2 recoil bosses in the Gen 2 recess and none in the Gen 1 recess, and that boss count is not confirmed by any Walther document.

Will a Gen 1 PDP plate fit a Gen 2 PDP slide?

This dataset says no and keeps the two generations as separate systems for exactly that reason. Both records state that the plate geometry differs and that the two generations are not plate-interchangeable, which is why there are 5 Gen 1 plate rows and 6 Gen 2 plate rows here rather than one shared set. The practical consequence is that a marketplace listing reading only "Walther PDP optic plate" does not tell you which slide it was cut for. The source is a third-party footprint reference rather than a Walther document, so treat it as the safe assumption and confirm the generation on the plate listing before ordering.

Which red dot mounts on a PDP without a plate?

One, in this dataset: the Holosun SCS-PDP-GR, which is built for the Gen 2 slide cut itself rather than to any optic footprint, per holosun.com's own product page. It is the only optic recorded as a direct fit on all 7 Gen 2 pistols here, and it is one of the two reasons a PDP 2.0 reaches 101 optic pages where a Gen 1 PDP reaches 98; the other is the Gen 2 plate that presents the Holosun 509T pattern. It is an open-emitter sight, so the enclosed options on this pistol all still arrive through a plate.

Does a Walther PDP plate take a Holosun 407K or 507K?

This dataset records no K-presenting plate for either generation, and its own source line is why the question is worth asking. The retailer plate guide that 4 of the 6 Gen 2 paths are drawn from lists adapter plates for the "Trijicon RMR, Shield RMSc, Holosun K, Vortex Venom/Noblex (Docter), C-More RTS, Aimpoint Acro, and Leupold DPP" footprints, which is 7 patterns where this dataset has recorded 5 of them. Holosun K and C-More STS are the two it has not attributed. Treat it as an open provenance question and confirm with the plate maker rather than reading the 6 plates recorded here as a claim that only 6 exist.

Is 101 optics really the most of any pistol here?

Tied for it. Across all 223 pistols in this dataset the median optic reach is 58. 11 pistols land on 101, the 7 Gen 2 PDP models and the 4 SIG P320 models that both C&H Precision and Outer Impact make plates for; 212 reach fewer and none reaches more. The next tier is the 15 Glock MOS pistols on 100. Against its own Gen 1 sibling the gap is three optics wide: the Holosun SCS built for this slide and the 2 Holosun 509T optics the Gen 2 509T plate adds.